How to Make Electric Series Parallel Testing Board for testing electric product

How to Make Electric Series Parallel Testing Board for testing electric product

Series Parallel Testing Board
How to Make Electric series board for testing electric product
How To Make An Electrical Series Testing Board

What is series lamp test?
A series test lamp is a way that electricians would test or find a “short circuit” somewhere in a residential building. … These same principles can be used to locate “high amperage drawing” devices in any circuit, just not as conveniently as screwing a light bulb into the fuse socket.

Visit My website for Electrical Jobs,Smart Home Automation Products & Systems”Diagram” https://rybonline.com/
Click here for online newspapers from all countries-FREE ONLINE NEWSPAPERS https://newspaper71.com/

Watching More Most viewed Videos
star delta connection without motor !Use incandescent light bulb STAR DELTA Starter

three phase dol starter Control overload Indicator Power Wiring diagram

3 phase DB main Power cable termination

star delta starter control circuit diagram ! star delta connection

Electrical house wiring 3 gang switch wiring diagram

Single Phase split AC indoor outdoor wiring diagram RYB ELECTRICAL

Star delta starter power circuit wiring diagram

singele phase DB wiring diagram single phase meter wiring diagram energy meter and MCB board

Reverse Forward DOL Starter Power and control Wiring

ring socket wiring diagram electrical house waring

two way light switch wiring diagram

emergency light switch wiring diagram!

cable glanding and termination low voltage switchgear

STAR DELTA STARTER REVERSE FORWARD POWER WIRING CONNECTION

Low Voltage Switchgear

How to Install cable tray Practical Skills

LCP lighting control panel using contactor and relay

tube light circuit wiring diagram

window ac wiring connection diagram RYB ELECTRICAL

FORWARD REVERSE STAR DELTA STARTER CONTROL WIRING CONNECTION DIAGRAM

3 PHASE DISTRIBUTION BOARD WIRING DIAGRAM

ELECTRICAL SWITCH BOARD WIRING DIAGRAM ! DIY HOUSE WIRING

11 kv Switchgear view

Door Bell Wiring multiple switch and series lamp

House Wiring Electrical Main Board

power socket installation and power socket outlet connection

THREE PHASE DOL STARTER CONTROL AND POWER WIRING DIAGRAM REVERSE FORWARD WITH LIMIT SWITCH

Electrician Hand tools part 1

THREE PHASE ENERGY METER CONNECTION WIRING DIAGRAM- METER BOARD

intermediate switch/3 way switch connection wiring diagram

How to Make AC to DC converter at Home

fan connection with regulator Wiring Diagram

Proper Joint Of Electric Wire Three Different Types Of Electrical Joints

A series test lamp is a way that electricians would test or find a “short circuit” somewhere in a residential building. Back when homes used “screw in fuses,” that had the same thread pattern as a light bulb (known as an Edison Thread), if one circuit in a house was repeatedly blowing fuses, the electrician would remove all loads from that circuit by unplugging all appliances and turning off all of the room switches in that circuit, remove the blown fuse and replace it with a regular high wattage light bulb rated for the house’s voltage (117V in USA). If the lamp glowed at all, it meant that there was load (less than infinite resistance) in the house wiring. If it did not light up at all, the electrician would go around turning switches on in that circuit to see which “switched branch of the circuit” had a partial short (60 ohms) or a dead short (0 ohms). If the series test lamp burned very dimly, it meant that the switched circuit had a small enough load that it would not blow the fuse. After checking the switched branches of the circuit, he would start plugging in appliances commonly used on that circuit. Whichever appliance caused his light in the fuse socket to burn brightly was the offending appliance that had a short in it.

These same principles can be used to locate “high amperage drawing” devices in any circuit, just not as conveniently as screwing a light bulb into the fuse socket.

19 Comments

  1. Enginer MD Manik Hossen on April 12, 2020 at 8:41 am

    Amar janamote series ta vul hoise vai kisu bujlamna… Light a newtal kamne jay

  2. Latif Quest on April 12, 2020 at 8:44 am

    Good video. What for is the direct socket

  3. Ajay Kumar on April 12, 2020 at 8:44 am

    Xgy oh

  4. SUJOY BISWAS on April 12, 2020 at 8:50 am

    Thank you

  5. RYB ELECTRICAL on April 12, 2020 at 8:51 am

    RYB ELECTRICAL visit website. https://rybonline.com

  6. Nazakat Ali on April 12, 2020 at 8:53 am

    First soket mein neutral nahi Diya.
    Jb k load m neutral must h

  7. Technical & Electrical Hub on April 12, 2020 at 8:54 am

    Bhai mere channel per bhi series wire h sirf 5 min me kese banaye bataya h usko bhi dekh lo

  8. Roncival Geronimo on April 12, 2020 at 9:00 am

    What kind of fuse you use? im beginner

  9. Nazakat Ali on April 12, 2020 at 9:04 am

    Wrong ckt

  10. Abid Sagar on April 12, 2020 at 9:09 am

    Grate job sir thanks

  11. Mazid Khan pleasgive your mobile n. on April 12, 2020 at 9:09 am

    Good axpleand

  12. Mosa 006 on April 12, 2020 at 9:17 am

    voice kore bole dile balo hoi bhai

  13. jesus loves u AFD on April 12, 2020 at 9:20 am

    Super 👍👍👌👌

  14. rajendra bahadure on April 12, 2020 at 9:26 am

    Switch kitene apr ke he sir

  15. riyajul islam on April 12, 2020 at 9:30 am

    ভাই এভাবে একে একে ড্রইং করে কোন অ্যাপস দিয়ে করেন বা একে একে দেখান এই অ্যাপসের নামটা কি বলবেন প্লিজ

  16. riyajul islam on April 12, 2020 at 9:32 am

    ভাই উত্তরটা দরকার ছিল কমেন্টের উত্তর দেন না কেন

  17. Umer Faruk on April 12, 2020 at 9:34 am

    How to test electrical components please tell us and shows

  18. JEwel on April 12, 2020 at 9:34 am

    Thanks 🙏

  19. kalidas p on April 12, 2020 at 9:37 am

    Super

Leave a Comment