now theres an egg glass thats more like the original piece but bigger. i might get that one. either way this rig is totally capable of destroying you. i load pretty tiny dabs and choke all to hell on the low setting. enjoy lol! got a quarter bucket of juicy ass peach pie resin here in michigan for a hundred 😀
Do you constantly get your smoke that dense with this piece? The stock one barely works for me. Dr dabber sent me the updated top. But doubt it will work this good. What temp and do you have any tips to make it work like this. Or did it work like this out of the box? Looks like they just came back in stock online too!!
Just got my ball rig which is banging awesome. Have a question about the way it sits on the Evo. It seems like the glass ball is stopping the magnetic base from seating out because it’s touching the outside rim. Is this normal?
finally decided to get an e-rig, hoping they had gotten better than the e-nails with their tight draw. normally use a mobius matrix w/ torch, but decided to bite the bullet and check out the new gen. of toys. after seeing your puffco comparison i decided to go w/ the boost as i have dabbed large dabs for a long time. my biggest worry was that the water piece didn’t look like it had enough cooling and the intake on the draw was a bit too narrow (like e-nails usually are). after seeing this and a long search i found two companies with them in stock and only one shipped (which they just started doing) in the usa. they only had one in stock and i managed to get it! thanks for the videos, this looks to make the purchase a worthy contender for replacing the torch and nail finally.
Do you like hot loading or cold better? When I reached out to dr dabber they recommended not to hot load it at all. But I have seen quite a few people that have done it
Hey your video definitely convinced me to get this rig. I watched another video of the J-Perc attachment and noticed that you advised putting the rubber on the carb cap which is not actually correct. The rubber snaps into the puck and that allows the carb cap to snap firming into the puck instead of moving around like you have it. Without water in the rig, you should be able to turn the piece completely upside down without the carp cap falling out which guarantees an air tight carp cap when pulling. Just wanted to share what I just learned from you and the other guy. Thanks
Review of the new Dr Dabber TDE (traditional dabbing experience) ball rig glass attachment
How is the cleaning of the parts pretty easy or
now theres an egg glass thats more like the original piece but bigger. i might get that one. either way this rig is totally capable of destroying you. i load pretty tiny dabs and choke all to hell on the low setting. enjoy lol! got a quarter bucket of juicy ass peach pie resin here in michigan for a hundred 😀
thank you for making this vid
This was an amazing review man! I just got one and absolutely love it!
What about the j perc
"Shit yeah!" I had to watch the video again just for that comment!
Nice!
Hey man seriously good video. Good editing. No bullshit talk. Real good thank you. Have an upvote.
Do you constantly get your smoke that dense with this piece? The stock one barely works for me. Dr dabber sent me the updated top. But doubt it will work this good. What temp and do you have any tips to make it work like this. Or did it work like this out of the box? Looks like they just came back in stock online too!!
Just got my ball rig which is banging awesome. Have a question about the way it sits on the Evo. It seems like the glass ball is stopping the magnetic base from seating out because it’s touching the outside rim. Is this normal?
Best temperture?
Do you notice it to be less harsh than the stock piece? The stock one burns my chest every time. Or makes me just want to puke
How noticeable is the chug compared to the normal glass attachment. Is it worth the price
Just received the the j-perc (ball rig is sold out) and relied on your video to figure how to configure it. Very helpful. Hits so lovely. Thanks!
Thanks for the video bro was just a little confused how the attachment would work but after seeing this definetely going to purchase
Bro you take the dab at exactly 710
Does it make more smoke than the standard glass attachment because the one it comes with don’t make big clouds like I want it to
This first evo attachment i Eva seeen bro, very nice lol I rock with CartaGang tho fam
Lol this guy makes terrible videos
Just grabbed one rn thanks to this review!
finally decided to get an e-rig, hoping they had gotten better than the e-nails with their tight draw. normally use a mobius matrix w/ torch, but decided to bite the bullet and check out the new gen. of toys. after seeing your puffco comparison i decided to go w/ the boost as i have dabbed large dabs for a long time. my biggest worry was that the water piece didn’t look like it had enough cooling and the intake on the draw was a bit too narrow (like e-nails usually are). after seeing this and a long search i found two companies with them in stock and only one shipped (which they just started doing) in the usa. they only had one in stock and i managed to get it! thanks for the videos, this looks to make the purchase a worthy contender for replacing the torch and nail finally.
Is cleaning the glass rig easy?
Do you like hot loading or cold better? When I reached out to dr dabber they recommended not to hot load it at all. But I have seen quite a few people that have done it
My clumsy ass wants one so bad but those thin pieces connecting the ball scare me. Just broke my original glass piece 😢
just got an e-mail from dr. dabber, they are back in stock!
Subbed cause your the first person I see doing real boost Evo reviews. Question what the original carb cap button do ya do anything with it?
So what times do you prefer on the norm the 20 or the 40 second hit
I am so glad someone has a review of this
So you’re telling me i been dabbing without the rubber on my carb cap this whole time? 😭
Hey your video definitely convinced me to get this rig. I watched another video of the J-Perc attachment and noticed that you advised putting the rubber on the carb cap which is not actually correct. The rubber snaps into the puck and that allows the carb cap to snap firming into the puck instead of moving around like you have it. Without water in the rig, you should be able to turn the piece completely upside down without the carp cap falling out which guarantees an air tight carp cap when pulling. Just wanted to share what I just learned from you and the other guy. Thanks
I was sold after the first hit
Awsome video bro ! Dr dabber should sponsor you . You have been on the top of it with the Boost Evo ! Pro and cons !!
Loving the up to date vids. Keep em coming. Hoping for a evo insert. They said they were trying things so well see. Thanks for the review again.
Just bought one 💪🏾
Does it every just not get cloudy like sometimes no cloud like the original glass ?